Uzin PE 650 Non Slump Primer 16kg bag (TnG or Hebel)

More about the product Substrate preparation The substrate must be sound, load-bearing, dry, free from cracks and free from materials (dirt, oil, grease) that would impair adhesion. Test the substrate in accordance with ap plicable standard or notices and report any deficiencies. Any adhesion-reducing or unstable layers, e.g. release agents, loose adhesives, compounds, covering or paint residues, etc. must be removed, e.g. by brushing, abrading, grinding or shot-blasting. Thoroughly vacuum loose material and dust. Allow the primer to dry completely. The datasheets for other used products have to be ob served. Application 1. Mix UZIN PE 650 with water to the desired consistency. The correct water quantity for 16 kg is 4 – 4.6 litres. However, as partial quantities are ususally mixed, 250  290 ml of water have to be used for 1 kg powder. Put cold, clear water into a clean container. Sprinkle in the powder while mixing vigorously until a smooth and lump-free compound is obtained. Mix only as much mor tar as can be applied within the working time of ap prox. 25 – 30 minutes*. 2. Apply a thin coat of UZIN PE 650 using a smoothing trowel. 3. Clean tools with water after use. Important notes A shelf life of 12 months when stored in moderately cool conditions, in the original packaging. The setting and drying times may become longer if the storage time is prolonged. The properties of the cured material are not affected. Carefully and tightly reseal opened packaging and use the contents as quickly as possible. Best applied between 15 – 25 °C, with the floor temperature above 15 °C and relative air humidity below 75%. Low temperatures and high air humidity lengthen the drying time. Whilst high temperatures and low air humidity shorten the drying time. For subsequent coats or thicknesses above 10 mm, epoxy resin primers such UZIN PE 460, gritted must be used. Not suitable as a primer for direct bonding of wood flooring, as well as the installation of floor coverings with 1comp. reaction resin adhesives. For subsequent installations of levelling compounds and the installation of wood flooring, please use UZIN 2comp. reaction resin adhesives or UZIN MK 250. When applying UZIN PE 650 by a roller, mix 16 kg of powder with 6.2 litres of water (approx. 390 ml per kg). Not suitable for use on water-soluble adhesive residues (e. g. sulphite adhesives) or tackifiers. Please look for suitable products in the UZIN Product Guide. On heavily jointed substrates, up to max. 5 kg of UZIN NC 182 can be added per 16 kg container (except on wooden substrates). Follow the generally acknowledged rules of the trade and technology for the installation of wood flooring and floor covering in respective of the applicable national standards (e.g. EN, DIN, OE, SIA, etc.) Seals of quality & ecolabels – Low chromate content acc. Regulation (EC) No. 1907/2006 (REACH) – EMICODE EC 1 PLUS / Very low emission – European Model EPD – Suitable for sustainable building certifications according to: DGNB, QNG, BNB, BREEAM, LEED Composition Special cements, mineral aggregates, redispersible poly mers and additives. Protection of the workplace and the environment Contains cement low in chromate acc. Regulation (EC) No. 1907/ 2006 (REACH). Cement produces strong alkaline on reaction with water. Avoid contact with skin and eyes. In the event of contact, rinse immediately with water. In the event of skin or eye irritation, seek medical advice. Use protective gloves. When mixing wear a protective dust-mask. Presents no physiological or ecological risk when fully cured. Basic prerequisites for best possible indoor air quality following floor covering work are conformity to standards of the work ing conditions, as well as thoroughly dry substrate, primer and smoothing compound. Disposal Where possible, collect product residues and re-use. Do not allow to get into drains, sewers or ground. Empty paper packaging is recyclable. Collect waste product, mix with wa ter, allow to harden, then dispose as Construction Waste.